Ideal for use in locksmithing, the PLASMA 40FV is a powerful plasma cutter with Inverter technology. . . QUALITY CUTTING WITHOUT DEFORMATION . Solid and reinforced design weighing only 20 kilos, it adapts to industrial and difficult environments to give a quality cut even on painted structures: . • Up to 15 mm for steel, stainless steel and cast iron. . • Up to 10 mm for Alu. and copper. . The 40FV PLASMA has a "mesh plate" mode that holds the arc when your torch is no longer in contact with the workpiece. The maximum power for a single phase product . . USER FRIENDLY INTERFACE . With this new interface, the settings are simplified thanks to 3 modes: . -Cutting of wire mesh. . -Cutting of solid sheet . -Measurement of air pressure . Visualize your settings with the built-in digital display. . . START UP WITHOUT HF . With the "Pilot arc" system, the arc begins without the need to touch the workpiece. This HF-free boot system avoids electromagnetic disturbances (radio, computer, telephony, medical equipment ...). . . EASY, FAST AND SAFE TO USE . 4 m torch with safety device on the trigger to prevent accidental or unintentional triggering. It is equipped with a ventilation corridor that insulates the electronic part from dust. To be connected to a compressed air source. . . HIGH-TECH POWER SUPPLY . The PLASMA 40FV is the latest generation of PLASMA 40FV with a large PFC, which makes it Flexible Voltage (85-265V). . • Thanks to this technology, the 40FV PLASMA operates on a single 230v-16a or 110v-32a socket, even in intensive use and on site extensions (100 m). . • The 40FV PLASMA is tested at the factory to withstand surges up to 400v. This makes it particularly suitable for operation on generators and in case of permanent overvoltages. . . Power supply: 230 V Mono . Consumption: 25A/32A (110V / 230V) . Cutting current: 10A to 40A . Duty cycle factor (40° - 60°): 32A . Pressure: 2.5 to 6 Bar . Thickness: Steel – 10 mm/Alu – 8 mm . 2 YEARS WARRANTY
Description
Ideal for use in locksmithing, the PLASMA 40FV is a powerful plasma cutter with Inverter technology. . . QUALITY CUTTING WITHOUT DEFORMATION . Solid and reinforced design weighing only 20 kilos, it adapts to industrial and difficult environments to give a quality cut even on painted structures: . • Up to 15 mm for steel, stainless steel and cast iron. . • Up to 10 mm for Alu. and copper. . The 40FV PLASMA has a "mesh plate" mode that holds the arc when your torch is no longer in contact with the workpiece. The maximum power for a single phase product . . USER FRIENDLY INTERFACE . With this new interface, the settings are simplified thanks to 3 modes: . -Cutting of wire mesh. . -Cutting of solid sheet . -Measurement of air pressure . Visualize your settings with the built-in digital display. . . START UP WITHOUT HF . With the "Pilot arc" system, the arc begins without the need to touch the workpiece. This HF-free boot system avoids electromagnetic disturbances (radio, computer, telephony, medical equipment ...). . . EASY, FAST AND SAFE TO USE . 4 m torch with safety device on the trigger to prevent accidental or unintentional triggering. It is equipped with a ventilation corridor that insulates the electronic part from dust. To be connected to a compressed air source. . . HIGH-TECH POWER SUPPLY . The PLASMA 40FV is the latest generation of PLASMA 40FV with a large PFC, which makes it Flexible Voltage (85-265V). . • Thanks to this technology, the 40FV PLASMA operates on a single 230v-16a or 110v-32a socket, even in intensive use and on site extensions (100 m). . • The 40FV PLASMA is tested at the factory to withstand surges up to 400v. This makes it particularly suitable for operation on generators and in case of permanent overvoltages. . . Power supply: 230 V Mono . Consumption: 25A/32A (110V / 230V) . Cutting current: 10A to 40A . Duty cycle factor (40° - 60°): 32A . Pressure: 2.5 to 6 Bar . Thickness: Steel – 10 mm/Alu – 8 mm . 2 YEARS WARRANTY